You are currently browsing all posts tagged with 'greenhouse'.
Displaying 1 - 3 of 3 entries.

plant stand 3

  • Posted on December 23, 2018 at 1:00 am

i have a mini candlestick for the third one. it’s about 3 inches tall. i planned to do the top as a 1-1/4″ wood disk with a tile mandala, so it would coordinate with the first two.
plant stand 3

plant stand 3
it looked good that way, and i may come back and make another like this, but…

then i found this charm in my stash and decided it would look better with the furniture, and be more unique.
plant stand 3
i glued it on with e6000 glue, it’s my favorite for glueing metal to things.
plant stand 3
top view,
plant stand 3
side view, it’s coming together now.

after the glue set,a much longer wait with this glue than with my trusty white glues, i sprayed the metal with white paint. the paint i have is a paint and primer all in one and the same one i use as a base coat when i paint on plastics. normal acrylics just peel off without the primer. i sprayed it lightly as i wanted some of the dark metal color to show through.
plant stand 3
the wood was painted with more normal acrylic paint. since i was painting it white as well i didn’t have to worry about overspray. if i had wanted to do the bottom a different color i would have had to either do an even coat of the spray on the whole thing as a solid base coat or else paint the top separately before gluing it on.
plant stand 3

Continue reading plant stand 3 »

Care to leave a comment? »

plant stand #1

  • Posted on December 21, 2018 at 2:38 pm

a conservatory needs lots of plant stands so that all the plants aren’t just sitting on the floor. i don’t have much time this close to christmas, but these are pretty quick so i figure i can get one done every day or so. once i get them all done, i’ll see how they fit in the greenhouse and decide which ones to use for this project and which will go in the box for future use.

the first one is just a simple wooden spool for the base and a disk for the top.
a greenhouse needs a lot of plant stands. here is the first
to give you an idea of size, the disk is 1-1/2″ in diameter

just like the plant stand in my mini sitting room, i glued the disk on with wood glue, being careful to center it, and then let the glue dry
a greenhouse needs a lot of plant stands. here is the first
and the side view
a greenhouse needs a lot of plant stands. here is the first

once the glue dried i painted it with the translucent white paint. i still can’t get the paint to show up in the photos, so didn’t bother posting a picture of that step.

i picked another mandala “tile” from the pile of remaining mandalas – you can fit a LOT of 1 to 1-1/4″ circles on a single piece of card stock, so i had plenty to choose from! – then modgepodged it on top and brushed with a thin coat to seal. quick as that the first one is done.
a greenhouse needs a lot of plant stands. here is the first

a greenhouse needs a lot of plant stands. here is the first

Continue reading plant stand #1 »

Care to leave a comment? »

making a simple plant stand

  • Posted on December 18, 2018 at 8:02 am

of course a conservatory wouldn’t be right with out at least a plant or two on plantstands. i didn’t have a lot of room in this one so decided to go fro just one.

i started with a tall tall skinny spool and a wood disk ( both from michaels) the spool is 2-3/4″ (7cm) tall x 1-1/8″ (28mm) wide. the disk is 1-1/2″ (35mm) in diameter
making a simple planter

first i glued the disk to the top of the spool, making sure it was centered.
making a simple planter

after the glue dried, i painted with translucent white paint (it doesn’t photograph that way but in real life this is whitish not just plain wood) you could get the same effect by thinning white acrylic paint with water, but i happened to have some that was pre-thinned so used that. next i did up a page of mandalas sized to fit. since i didn’t want to waste paper by only printing one circle and plan to make more planters for my second greenhouse later, i filled the page with a whole bunch of different ones. this time i printed it on plain printer paper, rather than card stock, because i wanted it to sit flush. i cut out and auditioned the various mandalas to see which i liked best. they always print in different tones than i get on my monitor, so i’m never sure which one(s) i will actually like till i try them. i chose this one because the tones work well with my floor tile. once i decided, the other circles got put away for later use and i used modge-podge to both attach and seal this one on top.
making a simple planter
the problem with zooming in, is that you see a lot of the imperfections that just aren’t noticeable when you look at them. case in point the pixelation on the tile is very hard to see in real life, and just makes for a soft, slightly worn look, perfect for the soft white stain on the wood.

a crocheted plant i made several years ago sits atop the new plant stand and the room is done. it’s too tiny to hold anything more.
finished room

while i was getting my camera, tuppence grabbed a couple of books, made herself a cup of hot tea, and claimed the room as her own.
tuppence settles in
her only complaint was that this close to christmas she thought the plant really ought to be a poinsettia or a christmas rose. i promised to look for one or make one for next year.

in spite of that i think she looks rather pleased with herself don’t you?

Continue reading making a simple plant stand »

Care to leave a comment? »